| 品牌：施诺依 | 型号：SNY-5 | 售后服务：质保一年 |
| 数控机床分类：数控车床 | 货号：45232 | 主电机功率：3.7kw |
| 运动方式：点位直线控制 | 加工尺寸范围：720mm | 主轴转速范围：0~2000rpm |
| 刀具数量：2 | 控制方式：半闭环控制 | 控制系统：施诺依 |
| 布局形式：卧式 | 动力类型：电动 | 用途：调整 |
| 适用行业：通用 | 是否跨境货源：否 |
出售SNY施诺依轮毂拉丝机 铝轮毂修复设备可定制 欢迎选购
轮毂表面位于车子外侧，很容易接受到来自外界的损坏，拉丝的轮毂也是一样，一旦受到损坏，大大降低轮毂整体的动感，破坏潮流的品位，对于很多对车子外观很在意的车主来说，即便是有一点点的擦伤，也难以接受。那么，轮毂表面总不可能完全不被伤害，总有那么一些时候，车主在开车或者停车，拐弯或者不小心撞击的时候，擦伤到轮毂，造成轮毂的或轻微或严重的损坏。这个时候，轮毂的修复显得异常必要和迫切了。
设备介绍
进一步提升，该款轮毂拉丝机免编程，激光探测，激光位移测距扫描；采用新的操作系统，界面清晰明了；智能保存数据；金属外壳，主轴抬高，操作稳定，能对轮毂拉丝加工修复。
轮毂拉丝机配置
1、配备工业电脑一台
2、激光检测
3、X/Z轴采用伺服电机
4、加大机身
轮毂拉丝机特点
1. 数据智能保存，可重复加工使用
2. 轮毂免编程自动拉丝修复机床，无需编程序
3.车床转速可调，工作状态可以达到0-1000转，且转速可调控
4 .针对不同轮毂，仅需简单操作便可获取轮毂加工数据
轮毂拉丝机对比
老式手动轮毂拉丝机
1.半自动操作，底盘较轻，机床工作时容易震动，程序复杂，对工人有技术要求 2.低转速，回转直径小，很难满足市场需求 3.操作时间长
新型轮毂拉丝机：
1. 转速 可达0-1000转，回转直径大加工尺寸可达28寸
2. 自动一键启动，简单方便，无功底1天即可操作
3.智能保存数据，重复数据一键启动，无需重复测量
Characteristics of Hub Wire Drawing Machine
1. Data Intelligent Preservation, Repeatable Processing and Use
2. Hub automatic drawing repair machine without programming, no programming
3. The lathe speed can be adjusted, the working state can reach 0-1000 revolutions, and the speed can be adjusted.
4. For different hubs, only simple operation is needed to obtain hubs processing data.
Comparison of Hub Drawing Machines
Old Manual Hub Drawing Machine
1. Semi-automatic operation, lighter chassis, easy vibration when machine tool working, complex procedures, technical requirements for workers 2. Low speed, small rotary diameter, it is difficult to meet market demand 3. Long operation time
New hub wire drawing machine:
1. Rotational speed can reach 0-1000 revolutions, rotary diameter and large processing size can reach 28 inches.
2. Automatic one-button start, simple and convenient, reactive power base can be operated in one day.
3. Intelligently save data, duplicate data start with one key, no need for duplicate measurement
轮毂修复后实拍图
轮毂拉丝机操作要求，注意事项
1、两人作业时，设备后方的操作人员不得正对拉丝机出口，以免工件万一飞出伤人。
2、轮毂拉丝机设备在正常运行状态下严禁调整轮毂拉丝深度，以免车刀失控造成设备、人身事故。
3、正确安装轮毂。认真检查上、下轴承座及升降丝杠润滑是否良好，确定出料上正面无人时方可开机。
4、轮毂拉丝机设备启动后立即检查轮毂摆幅是否在要求范围内，有无其它异常现象，否则应立即调整或关机处理。
5、严禁工件直接放在夹具上，严禁工作门不关闭无挡条直接放工件拉丝，以免工件飞出伤人。
6、拉丝机深度调整应适中，一般情况下的拉丝深度指示应在0.2-0.05之间，严禁超过0.3MM，以免造成设备或人身事故。
Operational requirements and precautions of hub wire drawing machine
1. When two persons work, the operator behind the equipment shall not export the wire drawing machine in order to avoid injuring the workpiece in case of flying out.
2. It is forbidden to adjust the drawing depth of hub wire drawing machine under normal operation, so as to avoid equipment and personal accidents caused by tool out of control.
3. Install hub correctly. Check carefully whether the lubrication of upper and lower bearing seats and lifting screw is good or not, and make sure that the machine can start when no one is on the front of the discharging material.
4. Check whether the hub swing is within the required range and if there are any other abnormal phenomena immediately after the start-up of the hub drawing machine equipment. Otherwise, it should be adjusted or shut down immediately.
5. It is strictly forbidden to place the workpiece directly on the fixture. It is strictly forbidden to place the workpiece wire drawing directly without closing the work door, so as to avoid the workpiece flying out and hurting people.
6. The adjustment of drawing machine depth should be moderate. In general, the indication of drawing depth should be between 0.2 and 0.05. It is strictly forbidden to exceed 0.3MM in order to avoid equipment or personal accidents.
至顾客
1、关于发货时间
付款后，要进行设备调试，确保设备到您手里可以正常使用，具体发货时间需与卖家协商。
2、关于物流
因为产品属于较重货物，公司一律物流发货，网上物流价格仅供参考，详情请联系卖家。
3、关于产品的价格
部分网上价格仅供参考，具体价格请致电卖家，详细咨询，
未经咨询下单厂家不发货的哟！
关于上述问题给您造成不变敬请谅解，购买后有什么问题可随时联系客服，我们将会一一为您解答！
